A brand sent us a two-year-old daypack last quarter. The liner had turned chalky and was flaking into the contents. The tag said PU. So did the tag on a commuter pack still selling after eight years of daily service. Both labels were honest. The polymers underneath were not the same. This article reads a polyurethane bag the way a formulator does: layer by layer, in about five minutes.
What a Polyurethane Bag Is Made Of
Polyurethane forms when a diisocyanate such as MDI reacts with a polyol. The result is a segmented copolymer. Hard segments from the isocyanate side deliver strength. Soft segments from the polyol side deliver flexibility. In bag construction, the polymer is spread or laminated as a film of roughly 25 to 60 g/m² over a woven or knit backing. The label calls it PU leather. The structure is coating plus fabric, and each layer carries its own specification.
Process history matters too. Legacy solvent lines carried DMF residue, which is why the EU now enforces a threshold below 10 ppm. Waterborne dispersion lines and solvent-free reactive systems have largely replaced them. Ask which line produced your material before you compare prices.

The PU Family: Ester, Polyether and TPU Compared
The word PU hides the decision that actually matters: which polyol built the soft segments. Ester polyols are cheaper and feel good, but water attacks their ester linkages. Polyether polyols resist that attack almost entirely. TPU is a thermoplastic elastomer, extruded into film and laminated rather than spread. The figures below come from incoming inspection data on production programs, not supplier brochures.
| Build | Coating Weight | Hydrostatic Head | Hydrolysis Life |
|---|---|---|---|
| PU, ester-based | 25–60 g/m² | 1,500–5,000 mm | 3–5 years |
| PU, polyether-based | 30–70 g/m² | 1,500–5,000 mm | 8–12 years |
| TPU laminate | 30–80 g/m² | 5,000–10,000 mm | 8–15 years |
| PVC (baseline) | 80–150 g/m² | 3,000–6,000 mm | 4–7 years |
The polyether upgrade costs roughly £2 to £5 more per pack. Against an 8-to-12-year service life, it is the best value decision in the category.
Hydrolysis: The Clock Inside Every Polyurethane Bag
Hydrolysis is water splitting the ester bonds inside the polymer. The reaction roughly doubles in speed for every 10°C rise. The same ester coating that lasts 3 to 5 years in a humid cupboard can last 6 to 9 years stored cool and dry. The failure sequence is fixed. First a chalky grey bloom appears on the inner face. Then a faint sweet smell develops. Then the coating flakes into powder. Finally it separates in sheets.
Accelerated aging follows ISO 1419: 70°C at 95 percent relative humidity for 7 or 14 days. Demand the report and the pass criterion, which should limit tear strength loss to around 20 percent.
Microfiber-backed bag material: how the backing changes flex and coating adhesion.

Choosing the Right PU: A Four-Question Decision Tree
Run the program through four questions. First, does the bag live indoors and commute? Specify polyether PU at 35 to 45 g/m² plus a DWR finish. It serves about a decade at a third of TPU cost. Second, does it face sustained rain or roll-top duty? Move to a TPU laminate rated 5,000 mm or higher, with taped seams. Third, does it work below minus 10°C? PU stiffens and cracks at the fold in those conditions, so TPU takes the panel. Fourth, is it a promo or liner build on a 3-to-5-year replacement cycle? Ester PU is acceptable there, and only there.
Whichever branch you take, demand the coating weight and the hydrostatic head in writing. Where a program needs zero solvent input with documented hydrolysis resistance, our hydrolysis-resistant silicone leather covers the same failure mode with a silicone surface instead. Both routes ship through our fashion and sports goods program with test reports attached.
Frequently asked questions:
- Is PU the same as vegan leather? PU is the most common vegan leather build, but the label alone says nothing about which polyol or process produced it.
- How long does a polyurethane bag last? Ester builds run 3 to 5 years, polyether builds 8 to 12, and TPU laminates 8 to 15 under normal use.
- Which matters more, coating weight or hydrostatic head? Weight drives wear life and hydrostatic head drives water column, so a specification needs both numbers.
Match the Build to Your Bag Program
Request PU and Silicone Samples
References
- https://mensbackpack.co.uk/articles/pu-vs-tpu-v… — Coating comparison: PU ester 25–60 g/m² at 1,500–5,000 mm and 3–5 years; polyether PU 8–12 years; TPU laminate 5,000–10,000 mm and 8–15 years; PVC 4–7 years; hydrolysis doubles per 10°C with ISO 1419 aging.
- https://eureka.patsnap.com/materials/pu-synthet… — Polyurethane synthetic leather chemistry: MDI or TDI reacted with polyester, polyether or polycarbonate polyols; hard and soft segment structure; solvent lines at 14–20 wt% with EU DMF below 10 ppm; peel strength 1.8–4.2 N/mm.